Corrosion-Resistant Pumping Solutions · The Core Power of Environmental Protection Processes
In wet FGD, limestone slurry pH is kept at 4.5–5.5, while chloride levels can reach 60,000–80,000 ppm, causing severe pitting and crevice corrosion. With 30 years of fluoroplastic and specialty alloy expertise, Meibao offers MB-F fluoroplastic pumps, MB-MD magnetic drive pumps, and MV-S vertical sump pumps—covering the full chain from acid-alkali neutralization and flocculant dosing to gypsum slurry discharge. Equipment is designed for 87,600 operating hours (10 years), greatly reducing maintenance replacement frequency.
Lift, return sludge, and waste sludge pumps in WWTPs face combined abrasion and corrosion. Aeration mixed liquor typically holds 1.5%–3.0% solids, with 50–200 μm sand causing cast iron impeller wear up to 0.5 mm/month. Meibao MB-D diaphragm metering pumps provide ±0.5% dosing accuracy and cut flocculant use by 12%–18%. At a 200,000 m³/day WWTP in Guangdong, annual chemical savings exceeded CNY 430,000. MV-S vertical sump pumps use duplex stainless steel or titanium wetted parts for 4–12 m tank depths, with maintenance-free bearing life ≥25,000 hours.
Slurry circulation and ammonia transfer pumps in FGD/SCR systems are critical for compliance at coal-fired power and steel sintering plants. Gypsum hardness (Mohs 3.5–4.0) and flow velocities of 4.5–7.5 m/s cause wear rates 20–50 times higher than clear water. Meibao's MB-F heavy-duty lined pump features 6.0–8.0 mm ultra-thick fluoroplastic lining with high-chromium cast iron backing. At a 2×660 MW Shandong plant, impeller life reached 14,200 hours—2.3 times longer than rubber-lined pumps. The MB-MD magnetic drive pump's seal-less design is widely used for 15%–25% ammonia water and NaOH transfer, eliminating fugitive VOC emissions.
Extreme Corrosion, Abrasion, and Emission Risks in Environmental Fluid Handling
Environmental pumping systems face a combined attack of high-chloride corrosion, abrasive high-solids slurries, and fugitive gas emissions. Wet FGD slurries can accumulate 60,000–80,000 ppm Cl⁻ at 50°C–65°C, while gypsum slurry abrasion and off-design cavitation rapidly destroy impellers. Meanwhile, mechanical seal leakage releases H₂S, NH₃, and VOCs—driving both equipment failure and regulatory penalties.
Fluoroplastic Lining, Hydraulic Optimization, and Zero-Leakage Magnetic Drive
Meibao applies three core solutions against corrosion, abrasion, and emissions. MB-F Series uses 6.0 mm FEP/PFA fluoroplastic lining with Hastelloy C-276 shaft sleeves—only 0.02 mm/year corrosion at 80,000 ppm Cl⁻ and 65°C. MV-S Series optimizes impeller hydraulics with duplex stainless steel CD4MCu, extending MTBF to 18,500 hours in gypsum slurry. MB-MD Series adopts a fully sealed magnetic drive, achieving 0.000% leakage and ≥99.7% emission reduction for H₂S and VOC service.
MB-MD Series employs a fully sealed containment shell with rare-earth magnets (NdFeB N45SH, max operating temp 150°C)—achieving 0.000% media leakage. Containment shell thickness is 1.2–1.5 mm (Hastelloy C-276) with eddy current losses ≤3.5%. For H₂S and VOC service, dual-containment shells with leak detection sensors (response time <0.5 seconds) reduce annual emissions by ≥99.7%.
Recommended Pumps for
Wastewater-&-Exhaust-Gas-Treatment
Each pump model is available in multiple material configurations to match the exact chemical and thermal requirements of your process.
Recommended
Recommended
Recommended
Recommended
Anti-Clogging Self-Priming Pump for Wastewater Lifting: 380 L/min Stable Flow, 0 Leakage, Annual Savings
The customer's three main problems—clogging, leakage, and self-priming failure—were closely connected:
• To prevent clogging, the impeller needs wide flow passages that can handle solid particles.
• To prevent leakage, the traditional shaft seal needs to be removed.
• To ensure reliable self-priming, the pump needs strong air-water separation and self-priming capability.
Explore Other Application Areas
Need Help Selecting the Right Pump for Your Process?
Our industry application engineers have direct process experience. Share your process data sheet and we'll provide a detailed pump recommendation with material selection, model number, and expected performance curve — typically within 48 hours.
WhatsApp
Facebook
LinkedIn
YouTube